What baud rate does the ZTS-3000-TR-WS-N01 use by default?

4800 bps, 8N1. It is a Modbus-RTU slave; default address 1.

What supply voltage does the ZTS-3000-TR-WS-N01 need?

DC 5–30 V (≤ 0.5 W (typical)).

How do I change the ZTS-3000-TR-WS-N01 Modbus address?

Write the device-address register with function code 0x06, one device on the bus at a time, then power-cycle. See the Configuration section above.

Is the ZTS-3000-TR-WS-N01 compatible with the Sankhya platform?

Yes — it is in the Sankhya RS-485 sensor library and the firmware-generation pipeline can produce node firmware for it.

What does the ZTS-3000-TR-WS-N01 not measure?

The ZTS-3000-TR-WS-N01 reports moisture and temperature only — it does not report EC, pH, N-P-K, salinity and TDS. On the same RS-485 bus, add EC: ZTS-3000-TR-ECWS-N01; pH: ZTS-3000-TR-PH-N01; N-P-K: ZTS-3002-TR-THNPKPH-N01.

Is the ZTS-3000-TR-WS-N01 the same as the Renke RS-WS-N01-TR?

They are register-compatible, not identical products. Both expose the same parameter set and the same Modbus register map, and Sankhya reads both with the ZTS_2in1 firmware profile. The Renke RS-WS-N01-TR is specified at DC 4.5–30 V against DC 5–30 V here. Housing, cable gland and probe material can differ between vendors, so check the electrical specs above before substituting one for the other.

Home / Sensors / ZTS-3000-TR-WS-N01

ZTS · RS-485 sensor

Zhaotaisheng

ZTS-3000-TR-WS-N01

2-in-1 soil moisture + temperature probe (RS-485 Modbus).

✓ Verified for SankhyaMoistureTemperatureVerification 0.95 · datasheet-confirmed

At a glance

The ZTS-3000-TR-WS-N01 is a 2-in-1 RS-485 soil probe reporting moisture and temperature over Modbus-RTU on RS-485 at 4800 bps, 8N1, on DC 5–30 V. This guide documents 4 registers, default Modbus address 1. It does not report EC, pH, N-P-K and others. For those on the same bus: EC → ZTS-3000-TR-ECWS-N01; pH → ZTS-3000-TR-PH-N01. It is register-compatible with the Renke RS-WS-N01-TR, which the same firmware profile reads unchanged. Sankhya firmware profile: ZTS_2in1.

Quick reference

Bus & electrical specs

Protocol

Modbus-RTU over RS-485

Default baud

4800 bps

Serial format

8N1

Function codes

0x03, 0x04, 0x06

Supply voltage

DC 5–30 V

Power

≤ 0.5 W (typical)

Default address

Ingress / housing

IP68

Probe / element

Stainless steel

Operating temp.

−40 to +80 °C (probe)

Firmware profile

ZTS_2in1

Specs sourced from: Official ZTS-3000-TR-* datasheets (R224068/R224069/R224070).

Modbus-RTU register map

Function codes 0x03, 0x04, 0x06 at 4800 bps, 8N1. Data registers are read with 0x03; configuration registers are written with 0x06. PLC column shows the 4xxxx Modbus holding-register convention.

Register	PLC	Parameter	Type	Scale	Unit	R/W	Notes
0000H	40001	Soil moisture	uint16	0.1	%	RO	Expanded 10x. Range 0-100%. Confirmed from official PDF response example: 0164H=356=35.6%.
0001H	40002	Soil temperature	int16	0.1	°C	RO	Expanded 10x. Negative in two's complement. Confirmed from official PDF: FFDDH=-35=-3.5°C. Range -40 to 80°C.
07D0H	42001	Device address	uint16	1	—	RW	Range 1-254. Factory default 1. Broadcast 0xFF for address discovery.
07D1H	42002	Baud rate	uint16	1	—	RW	Factory default 1 (4800 bps). 0=2400; 1=4800; 2=9600; 3=19200; 4=38400; 5=57600; 6=115200; 7=1200

Example poll

Worked query

# Read moisture + temperature (2 registers from 0x0000) request 01 03 00 00 00 02 C4 0B response 01 03 04 01 64 FF DD 3B B9 # 0164H=356 => moisture=35.6%, FFDDH=-35 => temperature=-3.5°C

Configuration

Changing address & baud rate

This probe is configured over the same RS-485 bus using Modbus write commands (function code 0x06). Configure one device at a time on the bus.

Set the Modbus slave address by writing register 07D0H (PLC 42001) with function code 0x06. Range 1-254. Factory default 1. Broadcast 0xFF for address discovery.
Set the baud rate by writing register 07D1H (PLC 42002). Values: 0=2400, 1=4800, 2=9600, 3=19200, 4=38400, 5=57600, 6=115200, 7=1200. Factory default 1 (4800 bps).
Power-cycle the probe after a configuration write for the change to take effect.

Field notes

Notes & caveats

Upgraded to 0.95. Official PDF uploaded and confirmed. 0000H=moisture, 0001H=temperature — confirmed from hex response example. Supports function codes 0x03/0x04/0x06. Stabilization <3 seconds. Baud enum extended to 8 values (adds 19200/38400/57600/115200/1200 vs earlier assumption of 3 values only).

FAQ

Common questions

What baud rate does the ZTS-3000-TR-WS-N01 use by default?: 4800 bps, 8N1. It is a Modbus-RTU slave; default address 1.
What supply voltage does the ZTS-3000-TR-WS-N01 need?: DC 5–30 V (≤ 0.5 W (typical)).
How do I change the ZTS-3000-TR-WS-N01 Modbus address?: Write the device-address register with function code 0x06, one device on the bus at a time, then power-cycle. See the Configuration section above.
Is the ZTS-3000-TR-WS-N01 compatible with the Sankhya platform?: Yes — it is in the Sankhya RS-485 sensor library and the firmware-generation pipeline can produce node firmware for it.
What does the ZTS-3000-TR-WS-N01 not measure?: The ZTS-3000-TR-WS-N01 reports moisture and temperature only — it does not report EC, pH, N-P-K, salinity and TDS. On the same RS-485 bus, add EC: ZTS-3000-TR-ECWS-N01; pH: ZTS-3000-TR-PH-N01; N-P-K: ZTS-3002-TR-THNPKPH-N01.
Is the ZTS-3000-TR-WS-N01 the same as the Renke RS-WS-N01-TR?: They are register-compatible, not identical products. Both expose the same parameter set and the same Modbus register map, and Sankhya reads both with the ZTS_2in1 firmware profile. The Renke RS-WS-N01-TR is specified at DC 4.5–30 V against DC 5–30 V here. Housing, cable gland and probe material can differ between vendors, so check the electrical specs above before substituting one for the other.

Alternatives

How this differs from similar models

How the ZTS-3000-TR-WS-N01 compares with the other RS-485 models in the Sankhya library. "Drop-in" means the same parameter set and the same register map, read by the same firmware profile.

Model	Relationship	Measures	Baud	Difference
Renke RS-WS-N01-TR	Drop-in	Moisture, Temperature	4800	Same parameter set and register map. Differs in supply range (DC 4.5–30 V) and registers documented here (2).
ZTS-3000-TR-ECWS-N01	Sibling	Moisture, Temperature, EC	4800	Adds EC.
ZTS-3001-TR-ECTHNPKPH-N01	Sibling	Moisture, Temperature, EC, pH, N-P-K, Salinity, TDS	4800	Adds EC, pH, N-P-K, salinity and TDS.
ZTS-3001-TR-ECTHPH-N01	Sibling	Moisture, Temperature, EC, pH, Salinity, TDS	4800	Adds EC, pH, salinity and TDS.
ZTS-3002-TR-THNPKPH-N01	Sibling	Moisture, Temperature, pH, N-P-K	4800	Adds pH and N-P-K.

Same family

Related ZTS sensors

Run this sensor on a Sankhya node

Every sensor on this page is in our RS-485 library. Pick your model, and the firmware-generation pipeline builds the Modbus (or ASCII) polling code for an ESP32-S3 node — no hand-coding the register math.